• GeoLogger digitizes the CPT data and synchronizes those data with depth
  • Encoder for the synchronisation of CPT data with depth
  • Clamp for pushing and pulling 36 mm CPT tubes and 55 mm casing tubes
  • Cable for the transfer of CPT data to the surface
  • 36 mm CPT tubes
  • Friction reducer used to reduce the lateral friction on the string of CPT tubes
  • 15 cm² and 10 cm² electric CPT cones
  • Software for the acquisition of CPT testing data
  • Software for processing and interpretation of CPT data
Gouda Geo-Equipment B.V.
Satellietbaan 8
2181 MH Hillegom
The Netherlands

Downloads

No downloads available

Base Kit for Electrical CPT with Standard Electric Cone

In the quotations Gouda-Geo issues a clear distinction is made between on one hand the CPT penetrometer pusher (this could either be a << truck-based >>, << crawler-based >>, << trailer-based >> or << stand-alone >> unit) and on the other hand the CPT system (this could either be mechanical or electrical CPT(U) system with automated or manual recording). This page describes the base kit one would need to do electrical CPT tests with a standard electric CPT cone with a CPT penetrometer pusher of one’s choice.

Electrical CPT testing with a standard electric CPT cone offers the opportunity to measure simultaneously the cone resistance (qc) and the local sleeve friction (fs) at predetermined intervals (every 10, 5, 2 or 1 cm depending on the required accuracy). Since the electric cone is equipped with a built-in XY-inclinometer, the deviation of the vertical axis in 2 directions is registered as well. All data are synchronised with depth.

For the performance of electrical CPT tests Gouda-Geo offers a complete and universal system to do these tests according to << national and international standards >>. It is to be used in combination with a PC computer and can be used on any penetrometer pusher and can be extended (at extra costs) with extra sensors, like pH/ORP, temperature, seismic, magnetometer, and alike.

The base kit consists of the following components:
 
 
GeoLogger Datalogger
 
The GeoLogger is the heart of the data acquisition system for CPT(U) testing. It is to be used in combination with a standard laptop or << industrial computer >> and << GeoExplorer data acquisition software >>.
 
The GeoLogger combines the following functions: The GeoLogger is compatible with all compression and subtraction type electrical CPT cones. The high-grade waterproof housing makes the unit extremely suitable for working in the field, its compact design assures the use of little space.
 
 
Depth Synchronisation
 
For synchronising the recorded CPT data with depth, an optical linear displacement encoder is required. This highly accurate device generates 10 pulses per cm and counts in 2 directions for optimum synchronisation. Comes complete with mounting bracket.
 
 
GeoExplorer Data Acquisition Software
 
GeoExplorer is a state-of-the-art software package specially designed for the on-site registration of Cone Penetration Testing data. It meets latest national and international standards and industry demands. Years of experience in the CPT industry make this software fulfil your demands and your wishes. GeoExplorer is modern and versatile and based on Microsoft Windows Technology.
 
GeoExplorer is easy to install and the user interface makes the CPT testing procedures clear and understandable. It can be controlled by means of the keyboard, scroll mouse, or touch-screen. It can also be used in conjunction with data acquisition equipment from other manufacturers. The user-interface language is available in both English and Dutch. French language will be available soon.
 
GeoExplorer is a software package that will be purchased; so you don't have to pay any annual license fee. The software is constantly updated and updates will be send to its users entirely free of charge.
 
<< Download >> a demo-version of GeoExplorer.
 
 
CPT-Office Presentation and Interpretation Software
 
CPT-Office is a Microsoft Windows based software package for the processing of CPT data, soil classification and the plotting of CPT test results.
 
The user friendly program structure is project oriented and provides, among other features, the possibility to edit project data and variables such as ground level, coordinates and water table in one simple step. Several individual CPT files or complete project files can be opened and processed simultaneously. All windows can be arranged according to the user's preferences.
 
Data can be viewed as tables and graphic plots and all CPT data can be edited freely while the raw data files remain unchanged. The user can opt for various languages (e.g. English, Dutch, German and more to follow), both for the program readings and for the plot versions.
 
Supports practically all data import formats, including the standardised GEF format. The processed data can be exported directly to Microsoft Excel or as ASCII, PDF and JPEG format.
 
 
Electric CPT Standard Cones
 
An electric CPT cone is a high-precision measuring instrument. Electric CPT cones are available with different cross sectional surfaces (10 cm² and 15 cm²) and either as compression type or subtraction type. The electric CPT cones proposed in this base kit are so-called subtraction type (S-type) cones. In S-type electric CPT cones, the strain gauges (sensors) measuring the cone resistance (qc) and the local friction (fs) are mounted on one single measuring body. This gives the subtraction type cones superior sturdiness over the compression type cones, who have 2 individual measuring elements overlaying each other.
 
The cone features a biaxial inclinometer, that measures the deviation from the vertical axis in 2 orientations during CPT testing. It is integrated in the cone body just above the conical tip. This assures rapid alarm, when the cone hits an obstacle or when it exceeds a previously set value.
 
All parameters are measured continuously and simultaneously.
 
The output signal from the cone is a voltage signal. It is amplified in the cone itself and transferred to the surface by means of a string of << CPT sounding cables >> provided with gold-plated Lemo connectors for uncompromised contact. This cable goes to the << GeoLogger datalogger >> where the analogue signal is converted into a digital signal. The digital signal is then sent to a computer for recording and further processing.
 
The piezocones are available in 2 different versions, i.e. a cone with a 10 cm² cross-section (Ø = 36 mm) and a 15 cm² cross-section (Ø = 44 mm). Please contact the Gouda-Geo sales department for advise on selecting the right cone for the job. Also be aware that one cone is not enough for any job (one=none). Always opt for at least 2 cones.
 
 
CPT Sounding Cables
 
A complete range of CPT sounding cables is available for electric cones. Note that a well selected cable will save time and annoyance during CPT testing. If you are in doubt, please consult the Gouda-Geo sales department to determine the appropriate cable for the job.
 
The CPT sounding cables are provided with unisex extension connectors that allow for unlimited extension of the CPT cable string. The cables are made of highly flexible PUR-TPE cable material featuring high tensile strength and wear resistance. The unisex extension connectors are high-quality Lemo connectors with gold-plated connecting pins.
 
A standard string of CPT sounding cables composes of: We do realise that one size does not fit all. It is therefore that the CPT sounding cable can be supplied in any length you might need. Selecting the right cable in order to optimize the cable lay-out is really important. Just specify the lengths required at order.
 
 
Clamp for Pushing and Pulling
 
The CPT push-and-pull clamp is purposely designed for automatic pushing and pulling of << CPT sounding tubes >> (Ø = 36 mm) and << casing tubes >> (Ø = 55 mm) during electrical CPT testing operations.
 
The CPT push-and-pull clamp has a pushing capacity of 200 kN and a pulling capacity of 260 kN. It fits in the yoke of a 100 kN as well as a 200 kN CPT penetrometer pusher. It can be used in combination with all type of electric CPT cones and << friction reducers >>.
 
The removable clamping blocks are made of hard metal. The force applied on the tubes by the clamp, is distributed evenly by the clamping blocks over the gripping area. This guarantees excellent seizing and prevents damaging or deformation of the sounding tube.
 
Pushing and pulling CPT sounding and casing tubes has eventually become an easy and quick job.
 
 
Friction Reducers
 
A friction reducer combines two purposes. It connects the electric CPT cone to the CPT sounding tubes and it reduces the lateral friction on the string of CPT sounding tubes during penetration.
 
The friction reducers are available either with cams or with a ring. The ring type friction reducer is primarily used in clays and clayey soils. The cam type friction reducer is mostly used in sands.
 
 
CPT Sounding Tubes
 
CPT sounding tubes are used to push the electric cone into the ground by means of a CPT penetrometer pusher. Gouda-Geo CPT sounding tubes meet the highest quality standards. The tube material is manufactured by one of Europe's leading steel manufacturers according to our own standards. No distinction whatsoever is made between tubes for 100 kN and 200 kN testing. All tubes are suitable for any pushing force and for any type of CPT test.
 
During production every single tube is checked automatically by means of sensors integrated in the lathe machine in order to comply with all national and international standards.
 
Gouda-Geo CPT sounding tubes are available with either standard (STD) tapered thread, quick-lock (QLK) double-entry rope thread, AR tapered rope thread and 2R tapered rope thread. Because of its superior characteristics, we recommend CPT sounding tubes with quick-lock (QLK) double-entry rope thread. The main advantages are the number of turns required to lock / unlock (only 2.5 turns), the improved strength of the thread (over 40% stronger than the standard tapered thread) and the relative ease to clean it.
 
 
Repair and Maintenance Kit
 
In order to assure excellent functioning of the above described system for electrical CPT testing, Gouda-Geo has assembled a kit for repair and maintenance. The kit comprises:
Background Reading
 
The book "Cone Penetration Testing in Geotechnical Practice" written by Tom Lunne, John J.M. Powell, and Peter K. Robertson is an brilliant book on Cone Penetration Testing (CPT and CPTU). It gives a very elaborate insight in technique and use of Cone Penetration Testing equipment. A must have for anyone working in the geotechnical field; the ultimate source for information.
 
The purpose of this book is to provide guidance on the specification, performance, use and interpretation of the Electric Cone Penetration Test (CPU), and in particular the Cone Penetration Test with pore pressure measurement (CPTU) commonly referred to as the "piezocone test."
 
Recommendation guidelines interpret a full range of geotechnical parameters from cone penetration data and relevant examples and case histories are given throughout the text.

Piezocone Dissipation test Water level meter CPT crawler CPT Electric cones Seismic CPT Magnetometer Gouda Jacket cone Soil sampler Dynamic penetrometer Cone Penetration Testing Piezometer CPTU Inclinometer
CPT truck Crawler-Truck Begemann cone Vane tester